Everyone wears out their Park Tool work stand clamp covers at some point. Find replacement covers for yours here. Each cover is constructed of soft, durable composite rubber. See below to determine which covers fit your Park Tool stand clamp: - 1002: fits 100-3X and 100-5X extreme range clamps - 1185: fits clamps on the repair stands PCS-9, PCS-10, PCS-11, and PCS-12 - 1259: fits 100-4X, 100-6X, 100-7X, and 100-15X clamps - 1960: fits 100-3D, 100-5D, and 100-25D Professional Micro Adjust Repair Stand Clamps - 468B: fits clamps with double cable reliefs, including 100-3C, 100-5C, 100-8C, 100-8Y, and 100-9C clamps - 467B: fits clamps with single cable relief, including PRS-2 through PRS-8 (for older-style clamps, non-current) - 468G: fits PCS-1 and PCS-2 clamps with double cable reliefs (clamp models: 100-1C, 100-1CA, and 100-2C) - 467G: fits PCS-1 and PCS-2 clamps with single cable relief (for older PCS-series stands only; not for current model stands) - 466: Rubber Replacement Clamp Cover Set (fits older clamps with plastic-dipped jaws)
Park Tool's 106-AC easily adapts the #106 Work Tray or PTH-1 Paper Towel Holder to fit 35mm-37mm upright tubes on PCS-9 Repair Stands, as well as 2003 and newer PCS-1, PCS-4, PCS-4-1, PCS-4-2 Repair Stands.
The RPP-1 offers simple but effective protection for your service area. This 32" tall pad prevents damage to bikes caused by being leaned against or knocked over onto your Park Tool professional repair stand. Covered with an attractive Park Tool blue vinyl finish for easy wiping off of dirt and grease. - Compatible with Park Tool Shop Repair Stands with a 2" diameter lower post, including all generations of PRS-2 and PRS-3 - Easily removed and installed with hook-and-loop material
A 6-inch (15cm) extension that easily mounts to the main beam of any PRS-22 or PRS-22.2 to accommodate longer wheelbase bikes with bottom bracket-to-front axle lengths over 28.75 inches, including CX, gravel and enduro style bikes.
The Travel and Storage Bag is a heavyweight nylon bag with a shoulder strap. This bag is designed for transporting and storing your Park Team Race Stand. It makes travel easy and convenient, while also protecting your stand.
Keep your most-needed bike repair tools and supplies close at hand with Park's Work Tray. It easily installs on your Park PRS-15, PRS-10, or PRS-11 Repair Stand (sold separately). And it features 2 separate compartments, a lube holder, a tool/towel bar, a tab system that holds plastic grocery bags and 2 receiver pods for extra accessories.
For wheels to perform properly, it's important that the rims be centered over the hubs. To check this, and to make precision adjustments, Park's Wheel Alignment Gauge (also called a dishing tool) is a must. It allows you to easily check centering on road, mountain and BMX wheels from 16 to 29 inches in diameter. It works with any hub width and its innovative design even allows it to be accurately used with the tire still on the wheel. The Wheel Alignment Gauge is a necessity for every wheelbuilder.
Topeak's FlashStand is a super work/display stand that folds up to become extremely portable as well! This affordable two-footed wonder supports your bike at the bottom bracket and down tube and raises the rear wheel with two adjustable-height feet. Take it along in the trunk of your car to dial-in your ride before your next adventure!
Includes a new tray/motor shroud, USB ports and oversized buttons to upgrade a Park Tool PRS-33 or PRS-33 AOK into the PRS-33.2 version controls and electronics.
Park's adjustable linkage shop clamp is found in more shops than any other professional level clamp. The 100-5C features solid cast aluminum construction and durable replaceable clamp covers. Clamp has reliefs on both jaws for cable routing, and feature replaceable jaw covers. - Fits PCS-4, PRS-5, PRS-6, and PRS-7 stands made after 6/96 - Fits bike frame tubes from 1" to 1 5/8" (25mm to 41mm) - The clamp jaws are nominally 4 inches (10cm) wide - Uses 468B jaw covers
A workstand is the backbone of any shop. Holding the bike at a convenient working height allows easy access for adjustments, cleaning and repair. The PCS-10.2 Deluxe Home Mechanic Repair Stand was designed and built using our 50 years of experience creating professional shop stands used in shops around the world. The unique three-point leg system and stout adjustable uprights create an extremely solid platform capable of handling bikes up to 80 lbs. (36kg). Easy to set up and use in a home shop, the PCS-10.2 also folds easily for transport or storage. - World famous Park Tool cam actuated, micro adjustable clamp that allows quick entry and exit and fits 1- to 3-inches (25mm–76mm) diameter tubes and seat posts of any shape and material - All steel structure for maximum stiffness and durability - Teardrop shaped tubing adds strength and ensures perfect positioning during use and folding - Folds quickly, easily and compactly for storage using aluminum quick release mechanisms and strong tubular support braces - Quick release height adjustment from 39- to 57-inches (99cm–145cm) - Durable textured powder coat finish - Super strong glass filled nylon composite fittings and top tube internals creating smooth rotation and secure positioning - Includes height adjustable compact tray to hold small parts, a few tools and the PTH-1 Paper Towel Holder (optional accessory)
A pro level workstand with a built-in digital weight scale. Stable tripod design folds down small for travel or use at the races. Additional clamp lever for tightening / releasing the clamp with ease. Clamp Head Non-marring rubber jaws 360° rotation Digital weight scale Clamp Height 122 cm to 183 cm (48” - 72”) Clamp Opening 1.9 cm to 4.5 cm (0.75” - 1.8”)
Page 1 of 1