- Replacement retaining clip for the Surly Tuggnut/Snuggnut
- QR adapter washer for the Surly Tuggnut/Hurdy/Snuggnut
Replacement push-down spring for the Surly Chain Tensioner
Replacement dropout screws for the Surly Cross Check. - Bolt length: 40mm
- Surly Chain Tensioner part
Surly Chain Tensioner part
Replacement dropout screws for the Surly Straggler. - Bolt length: 40mm
- Replacement slider for the Surly Tuggnut and Snuggnut
- Replacement thumb screw for the Surly Tuggnut/Snuggnut
Surly bearing adjust caps for Mr. Whirly and OD
The Mushroom Nuts thread into your Dummy frame (both the Big and the Big Fat kinds) and tensions your Dummy Bags, securing your various goods and things. - Made from durable stainless steel
Rear disc brake adaptor specifically designed ONLY for the Surly Troll, Ogre and ECR. - For use with 160mm rotor only - Brake caliper must be 74mm post mount compatible
Surly Surly Big Dummy Frame Protective Plug Insert. - Notice the tapered end of each plug, if the end of a tube is dented, tap the protective plug into the tube with a soft hammer to round the tube out - Designed to prevent damage to the front bridge tube while frame is being shipped - Doubles as a tool to help round out any damaged bridge tubes or upright tubes during use of the bike - The diameter of the plug is designed to round it out to the correct diameter so that it receives accessories properly
This fine pair of Surly 10/12 Adapter Washers is designed to adapt any 135, 170, or 190mm O.L.D. QR axle hub with a 142, 177 or 197mm spaced thru-axle frame. Make sure the QR axle on your wheel is the right length for the frame spacing. For instance: 190mm OLD QR goes with 197mm thru-axle spacing.
Surly wants you to be able to set up you ride just the way you want it. This pair of adapter washers make it so you can throw your favorite 135, 170, or 190mm O.L.D. 10mm solid axle hub into the rear end of a 142, 177, or 197mm spaced thru-axle frame. Add the adapters, add the wheel, install and tighten the nuts and, bam, you're ready to rip. Make sure the solid axle on your wheel is the right length for the frame spacing. For instance: 190mm OLD QR goes with 197mm thru-axle spacing.
Surly Stainless Steel Track Lockring. - Fits all but Campagnolo, Miche or Phil Wood - 5mm thick with 0.65mm lip for maximum thread and lockring wrench contact
Whether for derailleur clamp clearance, tire clearance, or personal preference, sometimes it can be advantageous to run the wheel further back in the dropouts. Monkey Nuts install into Surly horizontal dropouts to make spacing the wheel back easy. There are 3 different sets depending on the type of dropout and axle configuration the dropout is intended for. Simply select the correct version of Monkey Nut, install it into the frame, and slam the wheel all the way forward. Bang, done.
Surly Monkey Nuts v3 Dropout Spacers let you keep that rear wheel nice 'n' perpendicular in those horizontal dropouts, no matter how much of a diesel you are. So go ahead, stomp on the pedals and let the rooster tails fly. They're sold individually because most folks only need one on the drive side.
Rated fully KICKASS by a very authoritative entity who will remain unnamed, Surly's cast and polished stainless steel clamps won't rust or chip paint because they can't (even the black ones!). They're shiny! They look good! And most importantly, they deliver the clampability seatposts crave.
Like some of Surly's other chain tensioning devices, Snuggnut keeps your rear wheel from slipping forward in the dropout under the pedal load of your powerful gams. It's specifically designed for bikes that feature 12mm horizontal, vertical-slotted dropouts and is particularly suited for singlespeed application. Snuggnut is CNC-machined for durability and good looks, and shares many design features found on Tuggnut and Hurdy Gurdy. Note: The Snuggnut is compatible with horizontal thru-axle dropouts only. If using 10/12 Adapter Washers and QR wheels use a Tuggnut instead. Snuggnut is not for use with MDS Chips. Compatible models listed below: - Wednesday - ECR 29+ - ECR 27.5+ - Ogre - Krampus - Karate Monkey SS - Karate Monkey 27.5
Surly Thru-Axles are low-profile, bolted Thru-Axles are specifically designed for use with Surly thru-axle compatible frames. Offered in several sizes, for both front and rear wheels. 12x142 Rear Thru Axle: - Fits: Midnight Special and MDS Dropout bikes including Instigator, Legacy Karate Monkey & Legacy Krampus. 12x142/148 Rear Thru Axle: - Designed for frames with Surly Gnot Boost spacing (145mm), capable of working with 142 or 148mm rear hubs - Fits: Karate Monkey, Krampus, Troll, Ogre, ECR 12x177 Rear Thru Axle: - Fits: Wednesday 12x197 Rear Thru Axle: - Fits: Ice Cream Truck, Big Fat Dummy 12x100 Front Thru Axle: - Fits: Midnight Special 15x110 Front Thru Axle: - Fits: Karate Monkey, Krampus 15x150 Front Thru Axle: - Fits: Wednesday, Ice Cream Truck, Big Fat Dummy
If you've got rear-facing horizontal dropouts and you don't want your chain to slip when your rear wheel pulls forward, then Surly's got you covered. The Tuggnut is made from investment-cast stainless steel and it'll hold your wheel in place. Plus, it comes with an adapter for quick release axles and features an integrated bottle opener.
$33.50 - $50.00
The 12mm slotted MDS dropout is the newest chip for Surly's MDS equipped trail frames. You like chips, don't you? The 12mm slotted dropout chip uses a standard derailleur mount for maximum compatibility and is made of cast and machined 6061-T6 aluminum, with a fender eyelet. What's the coolest part about the 12mm slotted MDS chip, you ask? The fact that it also has the capability to run a 12 x 142mm thru-axle in a single speed configuration. This is good news because single speeds are good news. When you get an MDS equipped frame you're getting the option to set it up however you want. You can run a 142 x 12mm thru-axle rear end with a direct mount Shimano hanger, standard 135mm QR or The Mighty Singlespeed. The way this will work is that Surly complete bikes that feature the MDS will ship with whatever chip is compatible with derailleur spec. For instance, the complete Instigator 2.0 ships with the 142 x 12mm thru-axle Shimano chip. If you want to change it to a singlespeed later (and why wouldn't you?), all you have to do is get the SS chip. Frames will ship with all three MDS chips so pick your poison. The 142 x 12mm and 135mm QR chips are made of cast and machined 6061-T6 aluminum and The Mighty Singlespeed chip is 304 stainless steel, because the two words 'aluminum' and 'singlespeed' should never be too close to each other. Bad things can happen…. As you can see, the MDS gives you not just different build options, it lets you use a more varied selection of parts for your frame up builds. The MDS is featured on most of our trail bikes. That's right: Krampus Ops, Karate Monkey Ops, Instigator 2.0 and Ice Cream Truck frames all sport these puppies.
Hurdy Gurdy is another nifty device that keeps a rear wheel from slipping forward in the dropout under pedal load. It's designed for the Cross-Check's semi-horizontal front-loading dropouts, and will also work on many other similar dropouts. Hurdy Gurdy is investment cast of stainless steel for durability and good looks, and shares many of Tuggnut's design features. Its two axle holes allow for a wide variety of fore/aft wheel positions, it will work with standard QRs, bolted axles, and nutted axles up to 10mm.
Pair this kit with a cassette cog of your choosing (sold separately) and discover the joy and simplicity of a singlespeed without the cost of a new wheel. The Singlespeed Spacer Kit includes a variety of high quality aluminum spacers so you can dial your chainline and a stainless steel lockring to tighten everything down right.
Turn your geared bike into a singlespeed machine with Surly's Singleator. The Singleator mounts to your derailleur hanger and provides a smooth, quiet and adjustable means of tensioning the excess chain slack on any bike. It's made from strong forged steel and features a triple-sealed spring, large-cog capacity, chain guides, fully-adjustable chain line, floating pulley, and a stainless-steel pivot bushing. And, it works with both BMX and standard chains.
Surly OD Cups - Compatible with 24mm spindles
Page 1 of 1