Parts & Accessories
Zipp Speed Weaponry Valve Extender Wrench Set - Two 4 mm and 5 mm combination wrenches - Replacement wrenches required to properly install Zipp integrated valve extenders - Use with Zipp Tangente tubes with aluminum Presta valve and aluminum valve extender
$13.00 - $16.00
Whisky Parts Co. Tubeless Rim Tape.
$19.99 - $24.99
Booster thru-axle hub spacer kits are designed to give your non-Boost front and rear thru-axle hubs the boost they need to fit any Boost-compatible frame or fork.
The Deadbolt Ultralight Thru-Axles are offered in a 6mm flat button head design, for a flush, clean look. Lightweight, easy to use, and secure. - CNC-machined from 7000 series aluminum - Designed to fit all current Salsa thru-axle frames - For other frames, check with the manufacturer for compatibility and other specifications - 6mm hex wrench required for installation
Thru-Axle hub adapters allow the use of 100 mm front thru-axle hubs in 100 mm QR forks. -Allows the use of modern thru-axle wheels in forks designed for quick-release compatible hubs -100 mm front hub spacing only -CNC-machined AL-6061
Do you need to replace the right lock washer seal on your Alfine SG-S700 internally geared hub? If you're not sure, it might not be a bad idea, as contamination from damaged or worn seals is the kryptonite of virtually maintenance-free internally geared hubs.
Front end cap conversion kits for NoTubes Neo and Neo Ultimate - SealLock end caps feature a low friction U-cup seal that snaps into place
• Grade 3 balls and magnetite rust proof finish • Abec 5 precision and silicone w seals • 3 times cryogenic race treatment • Bearings sold individually, not as pair
Salsa's Stainless Flip-Offs use stainless steel rods for corrosion-resistant strength. They're strong, lightweight, and gorgeous. - Recommended for front rigid fork or full suspension use - Beautifully machined and hand friendly - Variety of sizes, sold as pairs or individually, front or rear - Black, Silver, Blue, Red, Green, Orange, Purple, or Pewter - More than just eye candy, they’re hand candy, as well - Weight: 49g
Durasync freehub bodies feature triple freehub bearings for increased axle stability to handle even greater vertical and torsional loads. This CNC machined durasync freehub is a direct replacement for your Neo hub, and includes pawls, springs, pawl retaining ring, and red freehub spacer. Bearings are pre-installed. - 6-pawl system provides 36 points of contact and 10-degree engagement for quick acceleration - Chromed steel bearings - Wide bearing stance and axle design reduces flex and adds durability - Low drag main seal prevents contamination and reduces resistance - Mini Driver has a Shimano HG spline, but is 10mm shorter to accept 11-speed cassettes with 10t cogs from Hope and OneUp Components
$17.00 - $27.00
SRAM's X0 conversion caps are the ticket for converting your X0 hubs to a different axle type.
WTB's TCS Brass Valves are your key to the excellence that is tubeless wheels and tires. A stepped lock nut adds compatibility among various rim drillings, a smooth pump interface makes adding air easy, and a removable core makes setting beads and injecting sealant a cinch.
WTB's TCS AL valves are aluminum to shed grams, and come in catchy anodized red, black, or blue. A stepped lock nut adds compatibility among various rim drillings, a smooth pump interface makes adding air easy, and a removable core makes setting beads and injecting sealant a cinch. - Presta - 46mm
Machined aluminum spacers for freehubs. Great for fine tuning freewheel and cassette placement or improving chainline. Also good for bottom bracket spacing with BSA BB cups. - Inner Diameter: 35.0mm - Outer Diameter: 40.7mm - Material: Aluminum - Finish: Polished - Bags of 10
This conversion kit allows you to use SRAM's 11-speed mountain cassette on your Stan's NoTubes wheels. Each kit includes an XD freehub, spacer, drive side end cap, and three sealed bearings.
Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Compatible with Shimano Front 9mm x 1 axle - Cone Wrench Size: 13mm - Threads: 9mm x 1 - Cone Diameter: 14.8mm - Dust Seal Diameter: 22mm - Length: 10.6mm - 1 cone per bag COMPATIBLE HUBS: - Tiagra 4400 Front - Shimano Sora HB-3300 Front - Shimano Acera HB-M330 Front - Shimano Nexave HB-T300 Front
Surly Ultra New Axle Kits are for upgrading the internals of your existing Surly New hubs or replacing the internals on your Surly Ultra New hubs. -Compatible with Surly New hubs (upgrade kit) and Surly Ultra New hubs (replacement kit) - Each kit contains an axle, two 6901 cartridge bearings, two aluminum dust shields, two stainless steel cones, two stainless steel 6x1mm bolts, and two stainless steel bolt washers - Axle is quick release and bolt-on compatible; bolts included, QR is NOT included - Standard Surly New hubs come stock with 7901 bearings; this kit uses 6901 bearings which are non-angular
- Replacement part for Surly hubs
Heavy duty and extra wide PVC rim strips for maximum tube protection.
Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Taiwanese hubs with 135mm spacing - Type: Hollow Axle - Threads: 9.5mm x 26tpi - Diameter: 9.5mm - Length: 146mm - 1 axle per bag
- Kit includes tape, 2 valves & 1 valve core wrench
Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Shimano / Japanese rear hubs with 135mm spacing - Type: Hollow Axle - Threads: 10mm x 1 - Diameter: 10mm - Length: 146mm - 1 axle per bag
The same spoke thread treatment used by Stan's pro wheel builders is now available to everyone. Stan's SRD Spoke Powder fills the threads of the spoke and functions as both a lubricant during assembly and a thread lock once built. Each bottle contains 24g (.8oz) which will treat approximately 300 wheels. The PTFE powder in Stan's SRD Spoke Powder acts as a barrier, keeping the metal of the nipple from bonding to the metal of the spoke and preventing spoke wind up during build or adjustment. In promoting a smoother turning nipple, the powder also ensures more accurate and consistent wheel builds, with less “ping and pop" during and after the build. The powder also fills the threads of the spoke to act as a thread lock that prevents loosening and de-tensioning and is particularly well suited for mechanically locking nipples such as Sapim's Secure Lock. - Improves tension consistency and overall build quality - Prevents spoke wind up - Offers secure thread lock between spoke and nipple - Prevents corrosion between spoke and nipple - Can be used dry or as a slurry - Works great with mechanically locking nipples
The Deadbolt Thru-Axles feature the classic-looking Salsa lever and can be adjusted to return to the desired position when properly tightened. Lightweight, easy to use, and secure. - CNC-machined from 7000 series aluminum - Designed to fit all current Salsa thru-axle frames - For other frames, check with the manufacturer for compatibility and other specifications
Surly's low-profile, bolted Thru-Axles are specifically designed for use with Surly thru-axle compatible frames. Not sure which one fits your bike? Get in touch, and we'll ensure you're choosing the correct axle for your application.
After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option. Our Lightning Bolt-On thru axles offer a high-quality, simple, lightweight alternative to that bulky handle. Available in a range of sizes that fit both front and rear wheels on all types of thru-axle-equipped bikes. - Lightning is Better—Our front and rear Lightning Bolt-On axles offer a stronger, more durable, lower profile, and lighter weight option to replace your stock thru-axles. - Low Profile—No more bulky handles to strike trail obstacles. Aerodynamic design. - Light Weight—Our axles are internally bored to remove unnecessary material without compromising strength. - Easy to install—Our matching front and rear Lightning Bolt-On Axles require only a standard 6mm hex wrench for easy installation and removal. - Better Tolerances—Manufactured in the USA to the tightest tolerances using aerospace materials and CNC manufacturing. No longer will your axle loosen while riding.
$58.00 - $65.00
Purchase our Kid Trailer axle for your bike, and share your stoke for cycling with your kids. Simplify your life by allowing quick and secure attachment of your trailer to your best and favorite bike. Enjoy the adventure. Robert Axles for Kid Trailers are designed specifically to fit your 12mm thru-axle bike and allow attachment of any hitch-mounted trailer. These fit any trailer that has two wheels and a single point of attachment to the axle. This includes all the two-wheeled child, pet, and cargo trailers such as Thule, Chariot, Burley, Instep, Carry Freedom, and many more. - The axle shaft and axle end are precision CNC-machined. - The axle shaft is 7075 aluminum and hard black-anodized for rugged durability. - The stainless steel axle end allows for mounting of the hitch provided with your trailer. - Hardware for attachment of the hitch is included; the hitch, itself, is not. - No special tools required. Design allows for wheel installation and removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world.
$62.00 - $65.00
Yes! A 12mm thru-axle adapter for BOB Trailers. These Robert Axles for BOB Trailers are specifically engineered to attach the proven BOB Trailer to your thru-axle-equipped bike. Take full advantage of your modern bike with 12mm thru-axles and harness the rigidity of the thru-axle to haul your BOB Trailer. Set out on any adventure, big or small. Great for off-road tours, trail building, hauling cargo, and more! - The axle shaft and axle end are precision CNC-machined. - The axle shaft is 7075 aluminum and hard black-anodized for rugged durability. - The axle ends are stainless steel which allows for mounting of the BOB Trailer bobbins. - No special tools required. The design allows for wheel installation or removal using your standard 5mm hex wrench. - Please note: This axle does not come with the BOB Trailer bobbins (those are available separately). Or, you can reuse your bobbins from the stock BOB Trailer Quick Release that came with your trailer. - Designed, built, and quality tested in the USA. Proven around the world.
Replacement cassette bodies for Oozy hubs and Spike hubs. - Shimano or SRAM - Alloy or Steel
Freehub bodies for Zipp Cognition hubs.
Page 1 of 4 Next page